#### Quiz-summary

0 of 16 questions completed

Questions:

- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16

#### Information

Click on Start Quiz button to take the Online test. Below are some articles to help you prepare for GATE exams.

**Mobile App**

You can install GATE Mobile App for unlimited online tests with answers.

**Exam Details**

Read my article on GATE exams for details of exam (eligibility criteria, format etc) and also post your questions or doubts.

**Online tests and Books**

My article on GATE Production and Industrial Engineering provides details to crack the exam with ease ( free online tests, recommended books, detailed syllabus).

You have already completed the quiz before. Hence you can not start it again.

Quiz is loading...

You must sign in or sign up to start the quiz.

You have to finish following quiz, to start this quiz:

#### Results

0 of 16 questions answered correctly

Your time:

Time has elapsed

You have reached 0 of 0 points, (0)

Average score | |

Your score |

#### Categories

- Not categorized 0%

Pos. | Name | Entered on | Points | Result |
---|---|---|---|---|

Table is loading | ||||

No data available | ||||

- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16

- Answered
- Review

- Question 1 of 16
##### 1. Question

In abrasive jet machining, as the distance between the nozzle tip and the work surface increases, the material removal rate

CorrectIncorrect - Question 2 of 16
##### 2. Question

Which one of the following is NOT a decision taken during the aggregate production planning stage?

CorrectIncorrect - Question 3 of 16
##### 3. Question

A process needs to be standardized for method and time. Which one of the following represents the sequence of work study experiments?

CorrectIncorrect - Question 4 of 16
##### 4. Question

x+2y+z = 4,2x+y+2z = 5,x-y+z = 1.The system of algebraic equations given above has

CorrectIncorrect - Question 5 of 16
##### 5. Question

A box contains 4 red balls and 6 black balls. Three balls are selected randomly from the box one after another, without replacement. The probability that the selected set contains one red ball and two black balls is

CorrectIncorrect - Question 6 of 16
##### 6. Question

The state of stress at a point under plane stress condition is σxx = 40 MPa, σyy = 100 MPa and τxy = 40 MPa. The radius of the Mohr’s circle representing the given state of stress in MPa is

CorrectIncorrect - Question 7 of 16
##### 7. Question

Water (Cp = 4.18 kJ/kg.K) at 80°C enters a counterflow heat exchanger with a mass flow rate of 0.5 kg/s. Air (Cp = 1 kJ/kg.K) enters at 30°C with a mass flow rate of 2.09 kg/s. If the effectiveness of the heat exchanger is 0.8, the LMTD (in °C) is

CorrectIncorrect - Question 8 of 16
##### 8. Question

In a DC arc welding operation, the voltage-arc length characteristic was obtained as Varc = 20+5l where the arc length l was varied between 5 mm and 7 mm. Here Varc denotes the arc voltage in Volts. The arc current was varied from 400 A to 500 A. Assuming linear power source characteristic, the open circuit voltage and the short circuit current for the welding operation are

CorrectIncorrect - Question 9 of 16
##### 9. Question

In a single pass rolling process using 410 mm diameter steel rollers, a strip of width 140 mm and thickness 8 mm undergoes 10 % reduction of thickness. The angle of bite in radians is

CorrectIncorrect - Question 10 of 16
##### 10. Question

A sine bar has a length of 250 mm. Each roller has a diameter of 20 mm. During taper angle measurement of a component, the height from the surface plate to the centre of a roller is 100 mm. The calculated taper angle (in degrees) is

CorrectIncorrect - Question 11 of 16
##### 11. Question

Match the following plastic products with their most appropriate materials.

Products Materials

1. Gears P. Polymethylmethacrylate (PMMA)

2. Helmets Q. Polyamides (PA)

3. Lenses R. Polyethylene (PE)

4. Food packaging S. Acrylonitrile-butadiene-styrene (ABS)CorrectIncorrect - Question 12 of 16
##### 12. Question

In a shaping process, the number of double strokes per minute is 30 and the quick return ratio is 0.6.If the length of the stroke is 250 mm, the average cutting velocity in m/min is

CorrectIncorrect - Question 13 of 16
##### 13. Question

For a linear programming problem, the set of constraints x+y ≤ 2, 3x+5y ≥ 15, x ≥ 0 and y ≥ 0 leads to

CorrectIncorrect - Question 14 of 16
##### 14. Question

A milk vendor incurs an overstocking cost of Rs. 2 per litre and a shortage cost of Rs. 0.5 per litre. The demand is uniformly distributed between 1 litre and 6 litres. Using the Newsvendor Model, the maximum quantity of milk in litre(s) the vendor should order is

CorrectIncorrect - Question 15 of 16
##### 15. Question

The specification limits for the weight of a product are 13.1 kg and 15 kg. If the process has a variance of weight 0.05 kg2, then the process capability index is

CorrectIncorrect - Question 16 of 16
##### 16. Question

On an average, there are 30 customers in a queue. If the arrival rate of customers into the system is 16 customers per hour and on average 32 customers leave the system per hour, then the average number of customers in the system is

CorrectIncorrect