0 of 20 questions completed
Click on Start Quiz button to take the Online test.Below materials will help you crack IES Exams with Ease.
You can install IES Android Mobile App for unlimited Online tests with answers and explanation.
Free Materials Download
You can download IES Exam Papers for free.
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
0 of 20 questions answered correctly
Time has elapsed
You have reached 0 of 0 points, (0)
- Not categorized 0%
|Table is loading|
|No data available|
- Question 1 of 20
In a circular shaft of diameter d,subjected to a torque r,the maximum shear stress induced isCorrectIncorrect
- Question 2 of 20
Which of the following terms represents the torque corresponding to a twist of one radian in a shaft over its unit length?CorrectIncorrect
- Question 3 of 20
If a shaft is turning at N r.p.m. and the mean torque to which the shaft is subjected is T N-m, the power transmitted by the shaft in kW would beCorrectIncorrect
- Question 4 of 20
The polar modulus of a circular shaft of diameter d isCorrectIncorrect
- Question 5 of 20
If a shaft rotates at 100 r.p.m. and is subjected to a torque of 3000 N-m, the power transmitted in kW would beCorrectIncorrect
- Question 6 of 20
A bar AB of diameter 40 mm and 4 m long is rigidly fixed at its ends.A torque 600 N-m is applied at a section of the bar, 1 m from end A.The fixing couples TA and TB at the supports A and B, respectively areCorrectIncorrect
- Question 7 of 20
The maximum number of unknown forces that can be determined in a concurrent coplanar force system under equilibrium isCorrectIncorrect
- Question 8 of 20
If a cantilever beam of span L and flexural rigidity EI carries a moment M at the free end, the deflection at that end isCorrectIncorrect
- Question 9 of 20
The maximum bending moment under a particular point load among a train of point loads crossing a simply supported girder occurs when that load isCorrectIncorrect
- Question 10 of 20
A uniformly distributed load of length 8 m crosses a simply supported girder of span 20 m. The maximum bending moment at the left quarter-span point occurs when the distance between the point of CG of the total load and mid-span isCorrectIncorrect
- Question 11 of 20
Consider the following statements :
1.The principle of superposition will hold good for the analysis of linear structural systems only.
2.The stress in a structural member due to several applied forces is the sum of the effects due to each of such forces,applied one at a time, only if the Hooke’s law holds good.
3.Internal stresses may not be caused resulting from lack of fit of a structural member. Which of these statements are correct?CorrectIncorrect
- Question 12 of 20
Consider the following statements
1.A properly constrained rigid system has several degrees of freedom.
2.The number of degrees of freedom of a locomotive moving on a railway track is only two.
3.A floating ship has six degrees of freedom. Which of these statements is/are correct?CorrectIncorrect
- Question 13 of 20
A suspension bridge with a two-hinged stiffening girder is staticallyCorrectIncorrect
- Question 14 of 20
The moment required to rotate the near end of a prismatic beam through unit angle without translation, when the far end is fixed, isCorrectIncorrect
- Question 15 of 20
The Muller-Breslau principle in structural analysis is used forCorrectIncorrect
- Question 16 of 20
Consider the following parameters with regards to slenderness ratio of a compression member :
3.Length of member
4.Support end conditions On which of these parameters does the slenderness ratio of a compression member depend?CorrectIncorrect
- Question 17 of 20
Two equal angles, each being ISA 100 mm x 100 mm of thickness 10 mm, are placed back-to-back and connected to either side of a gusset plate through a single row of 16mm diameter rivets in double shear. The effective areas of the connected and unconnected legs of each of these angles are 775 mm 2 and 950 mm2 respectively. If these angles are not tack-riveted, the net effective area of this pair of angles isCorrectIncorrect
- Question 18 of 20
When the effect of wind or earthquake load is taken into account in the design of a riveted connection,the permissible stresses in rivets may be exceeded byCorrectIncorrect
- Question 19 of 20
A mild steel flat subjected to a tensile force of 840 kN is connected to a gusset plate using rivets. If the permissible forces required per
(i) to shear a single rivet,
(ii) to crush the rivet and
(iii) to tear the plate are50 kN,80 kN and 60 kN respectively,
then the number of rivets required isCorrectIncorrect
- Question 20 of 20
The effective throat thickness of a fillet weld depends uponCorrectIncorrect
Leaderboard: IES Civil 4
|Table is loading|
|No data available|